![srw2024 downloading code using xmodem with putty srw2024 downloading code using xmodem with putty](https://64.media.tumblr.com/4735706cbf052d58f62f75e0bd2af927/9027e150c5ccbd76-02/s400x600/e845b9494c67d15ba4d7381e9c62a1be8dd09bb0.jpg)
![srw2024 downloading code using xmodem with putty srw2024 downloading code using xmodem with putty](http://entrancementhoney.weebly.com/uploads/1/2/4/2/124214554/653406723.jpeg)
- #Srw2024 downloading code using xmodem with putty serial
- #Srw2024 downloading code using xmodem with putty software
- #Srw2024 downloading code using xmodem with putty download
#Srw2024 downloading code using xmodem with putty download
I am now in the download loop:Downloading code using XMODEM.Edited at 16:04 UTC.Package WordList::Password::10Million::Top100000 To abort and enter prom.Preparing to decompress.The flash code is NOT valid!Image in address: 0x420000 - Check Sum error!Switching to the second image.Preparing to decompress.The flash code is NOT valid!Image in address: 0x0 - Check Sum error!Both images are not valid.Please download a new image.Downloading code using XMODEM.- Download complete -Wrong file format. D-Cache 16 KB.Ĭache Enabled.Autoboot in 2 seconds - press RETURN or Esc.
#Srw2024 downloading code using xmodem with putty software
Sectors = 119Are you sure (Y/N)? YEnter First flash sector (1 - 119): 1Enter Last flash sector (1 - 119): 119Are you sure (Y/N)? YErasing flash sector(s) 1 - 119 please waitFlash sector(s) erased.Perform WARM BOOT.Boot1 Checksum Test.PASSBoot2 Checksum Test.PASSFlash Image Validation Test.PASSBOOT Software Version 1.0.0.12 Built 0 15:46:33Carrier board, based on PPC8247128 MByte SDRAM. Writing aborted.This is the file name I used: PowerConnect34XXboot-10101.rfbHere is my log:Advanced menu1 Stacking port menu2 Erase Flash Sectors3 Image menu4 Stack menu5 MAC and Board Info menu6 MFG mode menu7 Debug mode menu8 BackEnter your choice or press 'ESC' to exit:Warning!Ībout to erase flash!FLASH size = 0xfe0000. I followed the steps and it went smoothly however, I received this error: Wrong file format. NSV, The boot code needsto be 1.0.1.01 or this boot loop will happen. To abort and enter prom.Preparing to decompress.100%Image in address: 0x420000 - Check Sum error!Switching to the second image.Preparing to decompress.100%Decompressing SW from image-1COMPLH5, Decompressing file: Version not supported!Switching to the second image.Perform WARM BOOT.Boot1 Checksum Test.PASSBoot2 Checksum Test.PASSFlash Image Validation at 19:11 UTC. Cache Enabled.Autoboot in 2 seconds - press RETURN or Esc. Intelectron motion detector bc8700kw manual.
#Srw2024 downloading code using xmodem with putty serial
(Shown below)I have tried to update the firmware and boot code from and so far I have tried these two &.I am using HyperTerminal and serial to Xmodem the software to the switch, the firmware seems to go through, but the boot code ends up giving me the following error on boot: 'COMPLH5, Decompressing file: Version not supported!' Any suggestions Spiceheads? Boot1 Checksum Test.PASSBoot2 Checksum Test.PASSFlash Image Validation Test.PASSBOOT Software Version 1.0.0.12 Built 0 15:46:33Carrier board, based on PPC8247128 MByte SDRAM. I may have took a wrong turn, because now the switch is in a loop at boot. I am trying to set the switch up so that it is back to factory defaults. PuTTYcmdSender tool to send cmd to multiple putty windows. Keyboard shortcuts for pre-defined command. Integrates all features of PuTTY cygterm project (PuTTYcyg), PuTTYSC. Integrates HyperLink of PuTTY NuTTY project. Integrates Ymodem,Xmodem,Zmodem,FTP,TFTP,SCP, file transfert protocols. Portability (use of directories structure). Additionally, I used a very old Compaq Armada laptop running XP32 to connect to the SRW2024 switch.įeatures. I found a version of the 1.0.0.86 code on some obscure FTP server. Topic Includes: I bricked my SRW2024 switch by installing the 1.2.2b firmware straight-away.